Hi there All,
I do know it’s been tough to stay affected person whereas we type all of this out however we’d moderately get as many anomalies sorted after the primary spherical of shipments earlier than persevering with to ship extra items. The excellent news is that issues are trying promising from right here.
Bumpy Roads
Whereas our new facet panels have a a lot cleaner match than the originals, that they had a good squeeze between the back and front covers. We’ve had some Argos homeowners contact us a couple of nook that might get pushed out from flush once in a while throughout common use. After re-confirming with our drawings, our provider sadly didn’t account for the coating/end utilized on the facet panels and the additional 1mm thickness added was sufficient to trigger some panels to have a nook pushed out below compression.
We’ve labored with the provider to get new panels made to the right spec. Within the meantime, we’re utilizing a belt sander and 3d printed jig to take away the additional 1mm off our current facet panels and refinishing them in order that we will ship out replacements to anybody with the difficulty freed from cost and hold constructing items. This can even enhance among the meeting delays and QC struggles we had with match and end over the previous few weeks.
In hindsight this could have been the very first thing that we checked but it surely’s straightforward to say that after the actual fact once we aren’t scrambling to type out our processes on the fly.
Steam Valve Leaking
We’ve observed some machines that drip water out of the steam wand regardless of being absolutely closed. Our steam wand is a personalized needle valve containing a quite simple needle design that works 95% of the time however isn’t as sturdy as we want. There are 2 points with it. The primary is that we had the needle/ plunger hardened. That is nice for longevity of the needle however sadly extra vulnerable to mild floor corrosion over time. The second situation is that the majority espresso machine steam valves are both comprised of brass which is a a lot softer metallic that may permit the needle to evolve and seat inside the orifice higher or they use a teflon seal.
We experimented with totally different teflon gasket and seal sizes choices that we hoped could possibly be added into our current valve to enhance sealing however all of them had points with the steam pushing them misplaced and blocking the stream path barely. We mentioned this with our provider and have provide you with a design that comes with an o-ring into the angled portion of the needle which ought to permit correct sealing with out the o-ring shifting inside the valve physique. This might be one thing that may be simply changed in time. Since we received’t want to fret concerning the needle sporting out, we’ve additionally opted to change the plunger again to a non-hardened chrome steel. A batch of 10 samples is predicted to be accomplished tomorrow and will ship out the next day. If these work as deliberate we’ll do a manufacturing run and swap these needle/plungers into our current valves in addition to ship them out to any those that have already got a machine with directions on how you can swap.
This won’t be a blocker for delivery machines out because it’s simply replaceable with a single wrench and an allen key.
PCB Spacers
We’ve had some homeowners report points with the machine not turning on or tripping gfci retailers. With the assistance of some extraordinarily affected person Argos homeowners we had been in a position to diagnose the difficulty which seemed to be a mixture of placement tolerances once we taped the PCB mounts with electrically resistive tape in addition to delivery hundreds inflicting the PCBs to barely rattle. This rattling mixed with tape that was positioned barely too low would permit a single solder on the again of the board to brief out. We’ve sourced a rubber spacer to be put in in an unused screw gap of the PCB which stands it off sufficient for there to be no manner for the PCB to contact the metallic plate it is mounted to.
Low fluid degree sensor
We simply had one Argos proprietor report the low fluid degree warning mild approaching even after refilling the water tank. After footage of the sensor, we discovered that the metallic probe had slid down the sleeve it sits in. This led to an air pocket above the probe which minimize off conductivity from the sensor via the water. These sensors come preassembled, however shifting ahead we’re going to make sure all sensors are tightened after putting in them.
Transport Updates
The facet panel changes, tightening low fluid degree sensors, and PCB rubber spacer have now all been added to our constructed up stock. We’ll do one other spherical of QC then start delivery all of our constructed up inventory out whereas persevering with to construct extra machines. I do know it’s been tough to stay affected person whereas we type all of this out however we’d moderately get as many anomalies sorted after the primary spherical of shipments earlier than persevering with to ship extra items.
Movies
Listed below are the movies we promised from the final electronic mail replace!
This new video was simply posted by Brian Quan from a latest San Francisco espresso meetup displaying the Vectis and Argos facet by facet! We’ve all been ready for it so that is thrilling to see the variations in dimension and pull approach. We should remember the fact that neither of the photographs pulled had been dialed in very properly with grind dimension and this Argos has a 6 bar spring whereas the Vectis makes use of an 8 bar which is able to make the type of shot pulled utterly totally different as talked about within the video. Regardless, it’s enjoyable to look at and see them each out within the wild.
